Sliding Wear Characteristics of Zn-15Sn Alloy with Nano B4C Reinforced Composites

Jump To References Section

Authors

  • Mechanical Engineering Department, Ballari Institute of Technology and Management, Ballari - 583102, Karnataka ,IN
  • Mechanical Engineering Department, Ballari Institute of Technology and Management, Ballari - 583102, Karnataka ,IN
  • Department of Mechanical Engineering, KLE Technological University, Dr. M. S. Sheshgiri Campus, Belagavi - 590008, Karnataka ,IN
  • Department of Mechanical Engineering, APS Polytechnic, Bengaluru - 560082, Karnataka ,IN
  • Department of Mechanical Engineering, Jyothy Institute of Technology, Bengaluru - 560082, Karnataka ,IN
  • Aircraft Research and Design Centre, HAL, Bengaluru - 560037, Karnataka ,IN
  • Aircraft Research and Design Centre, HAL, Bengaluru - 560037, Karnataka ,IN

DOI:

https://doi.org/10.18311/jmmf/2024/44052

Keywords:

B4C Particulates, Sliding Speed and Load, Stirs Casting, Wear Mechanism, Zn85-Sn15

Abstract

In the current investigation, high pin-on-disc wear testing equipment was used to examine the impact of modest additions of nano B4C on the wear behaviour of a Zn alloy (85Zn-15Sn). Zn-Sn alloy behaviour at a constant SD of 2000m under pressures (10N, 20N, 30N, and 40N) and sliding speeds (1.4, 1.8, 2.3 and 2.8 m/s) was investigated. Microanalysis with SEM/EDX was used to characterise the matrix and worn surfaces. According to the results, the wear rate of Zn alloy rises with rising pressures, sliding speeds and distances in all situations examined and lowers with an additional level of 8 weight per cent B4C to the Zn alloy when tested. This is brought on by the partial refinement of Zn dendrites, as well as the precipitation hardening of solid solutions. The worn surface investigation suggests that the creation of a thick oxide layer during sliding enhances tribological features.

Downloads

Download data is not yet available.

Metrics

Metrics Loading ...

Downloads

Published

2024-07-22

How to Cite

Janamatti, S. V., Jadar, R., Angadi, S. B., Namdev, N., Kumar, S. M., Nagaral, M., & Prashanth, A. N. (2024). Sliding Wear Characteristics of Zn-15Sn Alloy with Nano B<sub>4</sub>C Reinforced Composites. Journal of Mines, Metals and Fuels, 72(4), 391–400. https://doi.org/10.18311/jmmf/2024/44052

Issue

Section

Articles
Received 2024-05-15
Accepted 2024-05-29
Published 2024-07-22

 

References

Kori SA, Prabhudev MS. Sliding wear characteristics of Al-7Si-0.3mg alloy with minor additions of copper at elevated temperature. Wear. 2011; 271(5-6):680-8. https://doi.org/10.1016/j.wear.2010.12.080 DOI: https://doi.org/10.1016/j.wear.2010.12.080

BM G, Hindi J, Hegde A, Sharma S, Kini A. Effect of machining parameters on tool life and surface roughness of AISI 1040 dual phase steel, Mater Res. 2022; 25. https://doi.org/10.1590/1980-5373-mr-2021-0351 DOI: https://doi.org/10.1590/1980-5373-mr-2021-0351

Prajapati JM. Friction and wear behaviour analysis of different journal bearing materials. Mater Sci Eng. 2013; 3(4):2141-6.

M. O. F. Technology, Hegde A. Corrosion behaviour of sintered austenitic stainless steel. 2012; 3(12):14-7.

Krishnan BR, Ramesh M. Experimental evaluation of Al-Zn-Al2O3 composite on piston analysis by CAE tools. Mech. Mech Eng. 2019; 23(1):212-7. https://doi.org/10.2478/mme-2019-0028 DOI: https://doi.org/10.2478/mme-2019-0028

Nagesh SN, Siddaraju C, Prakash SV, Ramesh MR. Characterisation of brake pads by variation in composition of friction materials. Procedia Mater Sci. 2014; 5:295-302. https://doi.org/10.1016/j.mspro.2014.07.270 DOI: https://doi.org/10.1016/j.mspro.2014.07.270

Manjunatha S, Manjaiah M, Basavarajappa S. Analysis of factors influencing dry sliding wear behaviour of laser remelted plasma sprayed mo coating using response surface methodology. Arch Metall Mater. 2018; 63(1):217-25. https://doi.org/10.1080/17515831.2017.1407473 DOI: https://doi.org/10.1080/17515831.2017.1407473

Anne G, Ramesh MR, Nayaka HS, Arya SB, Sahu S. Microstructure evolution and mechanical and corrosion behaviour of accumulative roll bonded mg-2%Zn/Al-7075 multilayered composite. J Mater Eng Perform. 2017; 26(4):1726-34. https://doi.org/10.1007/s11665-017-2576-z DOI: https://doi.org/10.1007/s11665-017-2576-z

Kumar A, Arafath MY, Gupta P, Kumar D, Hussain CM, Jamwal A. Microstructural and mechano-tribological behaviour of Al reinforced SiC-TiC hybrid metal matrix composite. Mater Today Proc. 2020; 21:1417-20. https://doi.org/10.1016/j.matpr.2019.08.186 DOI: https://doi.org/10.1016/j.matpr.2019.08.186

Liu L, Yang C, Sheng Y. Wear model based on real-time surface roughness and its effect on lubrication regimes. Tribol. 2018; 126:16-20. https://doi.org/10.1016/j.triboint.2018.05.010 DOI: https://doi.org/10.1016/j.triboint.2018.05.010

Kumar GBV, Gowtham P, Sai Ram PNVNS, Sai Ganesh V, Sai Praneeth P. Fabrication and tribological behaviour of Al3003-SiC reinforced MMCs. IOP Conf Ser Mater Sci Eng. 2021; 1185(1):012025. https://doi.org/10.1088/1757-899X/1185/1/012025 DOI: https://doi.org/10.1088/1757-899X/1185/1/012025

Ramesh BT. Dry sliding wear test conducted on pin-on-disk testing setup for Al6061-sic metal matrix composites fabricated by powder metallurgy. Int J Innov Sci Eng Technol. 2015; 2(6):264-70.

Nagaraj N, Mahendra KV, Nagaral M. Investigations on mechanical behaviour of micro graphite particulates reinforced Al-7Si alloy composites. IOP Conf Ser Mater Sci Eng. 2018, 310(1). https://doi.org/10.1088/1757-899X/310/1/012131 DOI: https://doi.org/10.1088/1757-899X/310/1/012131

Bharath V, Nagaral M, Auradi V, Kori SA. Preparation of 6061Al-Al 2 O 3 MMCs by stir casting and evaluation of mechanical and wear properties. Procedia Mater Sci. 2014; 6:1658-67. https://doi.org/10.1016/j.mspro.2014.07.151 DOI: https://doi.org/10.1016/j.mspro.2014.07.151

Yakoub NG. Effect of nano-zirconia addition on the tribological behaviour of Al-7075 nanocomposites. 2020; 9(8):417-21.

Ali A. Wear behaviour of Al6061/TiO2 composites synthesised by stir casting process. J Adv Eng Trends. 2021; 41(2):113-25. https://doi.org/10.21608/jaet.2021.55413.1081 DOI: https://doi.org/10.21608/jaet.2021.55413.1081

Kumar GBV, Panigrahy PP, Nithika S, Pramod R, Rao CSP. Assessment of mechanical and tribological characteristics of silicon nitride reinforced aluminium metal matrix composites. Compos. Part B Eng. 2019; 175:107138. https://doi.org/10.1016/j.compositesb.2019.107138 DOI: https://doi.org/10.1016/j.compositesb.2019.107138

Majzoobi GH, Rahmani K. Mechanical characterisation of Mg-B4 C nanocomposite fabricated at different strain rates. Int J Miner Metall Mater. 2020; 27(2):252-63. https://doi.org/10.1007/s12613-019-1902-x DOI: https://doi.org/10.1007/s12613-019-1902-x

Abbas A, Huang SJ, Ballóková B, Sülleiová K. Tribological effects of carbon nanotubes on magnesium alloy AZ31 and analysing ageing effects on CNTs/AZ31 composites fabricated by stir casting process. Tribol Int 2020; 142. https://doi.org/10.1016/j.triboint.2019.105982 DOI: https://doi.org/10.1016/j.triboint.2019.105982

Babic M, Ninkovic R, Rato, Rac A. Sliding wear behaviour of zn-al alloys in conditions of boundary lubrication. Ann. Univ. “Dunărea Jos” Galaţi Fascicle 2005; Viii:60-4.

Manjunatha TH, Basavaraj Y, Nagaral M, Venkataramana V, Harti JI. Investigations on the mechanical behaviour of Al7075 - nano B4 C composites. IOP Conf Ser Mater Sci Eng. 2018; 376(1):012091. https://doi.org/10.1088/1757-899X/376/1/012091 DOI: https://doi.org/10.1088/1757-899X/376/1/012091

Nagaral M, Auradi V, Prashant SN. Preparation and evaluation of mechanical and wear properties of al6061 reinforced with graphite and Sic. Int J Mech Eng Robot Res. 2012; 1(3):106-12.

Rameshkumar T, Rajendran I, Latha AD. Investigation on the mechanical and tribological properties of aluminium-tin based plain bearing material. Tribol Ind. 2010; 32(2):3-10.

Nagaral M. Wear behaviour of sic-reinforced Al6061 alloy metal matrix composites by using Taguchi’s techniques. Int J Res Eng Technol. 2014; 3(15):800-4. https://doi.org/10.15623/ijret.2014.0315150 DOI: https://doi.org/10.15623/ijret.2014.0315150

Prasad GP, Chittappa HC, Nagaral M, Auradi V. Influence of B4C reinforcement particles with varying sizes on the tensile failure and fractography of LM29 alloy composites. J Fail Anal Prev. 2020; 20(6):2078-86. https://doi.org/10.1007/s11668-020-01021-6 DOI: https://doi.org/10.1007/s11668-020-01021-6

Bharath V, Ajawan SS, Nagaral M, Auradi V, Kori SA. Characterisation and mechanical properties of 2014 aluminium alloy reinforced with Al2O3p composite produced by two-stage stir casting route. J Inst Eng Ser C. 2019; 100(2):277-82. https://doi.org/10.1007/s40032-018-0442-x DOI: https://doi.org/10.1007/s40032-018-0442-x

Baskaran S, Anandakrishnan V, Duraiselvam M. Investigations on dry sliding wear behaviour of in situ casted AA7075-TiC metal matrix composites by using Taguchi technique. Mater Des. 2014; (60):184-92. https://doi.org/10.1016/j.matdes.2014.03.074 DOI: https://doi.org/10.1016/j.matdes.2014.03.074

Adaveesh B, Halesh GM, Nagaral M, Mohan Kumar TS. Microstructure and tensile behaviour of B4C reinforced ZA43 alloy composites. IOP Conf Ser Mater Sci Eng. 2016; 149(1):012115. https://doi.org/10.1088/1757-899X/149/1/012115 DOI: https://doi.org/10.1088/1757-899X/149/1/012115

Mishra SK, Biswas S, Satapathy A. A study on processing, characterisation and erosion wear behaviour of silicon carbide particle filled ZA-27 metal matrix composites. Mater Des. 2014; 55:958-65. https://doi.org/10.1016/j.matdes.2013.10.069 DOI: https://doi.org/10.1016/j.matdes.2013.10.069

Manjunatha TH, Basavaraj Y, Venkata Ramana V. Wear analysis of Al7075 alloyed with nano B4C: A Taguchi approach. Mater Today Proc. 2021; 47(10):2603-7. https://doi.org/10.1016/j.matpr.2021.05.086 DOI: https://doi.org/10.1016/j.matpr.2021.05.086

Harichandran R, Selvakumar N. Microstructure and mechanical characterisation of (B4C+ h-BN)/Al hybrid nanocomposites processed by ultrasound-assisted casting. Int J Mech Sci. 2018; 144:814-26. https://doi.org/10.1016/j.ijmecsci.2017.08.039 DOI: https://doi.org/10.1016/j.ijmecsci.2017.08.039

Wei CB, Tian XB, Yang Y, Yang SQ, Fu RKY, Chu PK. Microstructure and tribological properties of Cu-Zn/TiN multilayers fabricated by dual magnetron sputtering. Surf Coatings Technol. 2007; 202(1):189-93. https://doi.org/10.1016/j.surfcoat.2007.05.013 DOI: https://doi.org/10.1016/j.surfcoat.2007.05.013

Prabu SB, Karunamoorthy L, Kathiresan S, Mohan B. Influence of stirring speed and stirring time on the distribution of particles in cast metal matrix composite. J Mater Process Technol. 2006; 171(2):268-73. https://doi.org/10.1016/j.jmatprotec.2005.06.071 DOI: https://doi.org/10.1016/j.jmatprotec.2005.06.071

Lo SHJ, Dionne S, Sahoo M, Hawthorne HM. Mechanical and tribological properties of zinc-aluminium metal-matrix composites. J Mater Sci. 1992; 27:8-9. https://doi. org/10.1007/BF01119723 DOI: https://doi.org/10.1007/BF01119723

Nirmala L, Yuvaraj C, Rao KP. Microstructural and mechanical behaviour of Zinc. IJMET. 2013; 4(4):243-8.

Prasad GP, Chittappa HC, Nagaral M, Auradi V. Influence of 40-micron size B4C particulates addition on the mechanical behaviour of LM29 alloy composites. 2018; 8(2):20-7.

Nagaral M, Auradi V, Parashivamurthy KI, Shivananda BK, Kori SA. Dry sliding wear behaviour of aluminium 6061-SiC-graphite particulates reinforced hybrid composites. IOP Conf Ser Mater Sci Eng. 2018; 310(1). https://doi.org/10.1088/1757-899X/310/1/012156 DOI: https://doi.org/10.1088/1757-899X/310/1/012156

Aherwar A, Patnaik A, Pruncu CI. Effect of B4C and waste porcelain ceramic particulate reinforcements on mechanical and tribological characteristics of high strength AA7075 based hybrid composite. J Mater Res Technol. 2020; 9(5):9882-94. https://doi.org/10.1016/j.jmrt.2020.07.003 DOI: https://doi.org/10.1016/j.jmrt.2020.07.003

Narayana K, Naveenn NS. Influence of heat treatment on mechanical and tribological properties of tin brass. Ijmeit. 2014; 2(5):238-43.

Singh KM, Chauhan AK. Comparison of mechanical and microstructural examination of Al7075 composites reinforced with micro and nano B4 C. Int J Mech Eng Technol. 2020; 11(4):8-15. https://doi.org/10.34218/IJMET.11.4.2020.002 DOI: https://doi.org/10.34218/IJMET.11.4.2020.002

Glaeser WA. Wear properties of heavy-loaded copper-based bearing alloys. Journal of Metals. 1983; 35(10):50-5. https://doi.org/10.1007/BF03338390 DOI: https://doi.org/10.1007/BF03338390

Most read articles by the same author(s)

1 2 > >>